Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Engineering 2311: Essential Fluid Engineering
Introduction to Engineering 2311
Course Description, Learning Outcomes, and Course Requirements (10:48)
Course Materials and Worksheet Download
Manual Introduction
UNIT A: Fluid Statics and Dynamics
Unit A Reading
Section 1: The Importance of Fluid Engineering (20:12)
Section 2: Properties of Water: Mass, Weight, and Density (11:13)
Section 3: Properties of Water: Pressure (14:37)
Section 4: Properties of Water: Velocity (15:47)
Section 5: Properties of Water: Friction (8:35)
Unit A Quiz
UNIT B: Energy and Friction
Unit B Reading
Section 1: Energy and Water Level (15:35)
Section 2: Energy and Water Level Further Discussion (14:49)
Section 3: Hydraulic Grade Line and Friction Loss (14:32)
Section 4: Hazen-Williams Equation and Friction (15:26)
Section 5: Minor Losses (24:26)
Unit B Quiz
UNIT C: Introduction to Total Dynamic Head
Unit C Reading
Section 1: The Watershape Advisor Worksheets (20:58)
Section 2: Component Losses (18:04)
Section 3: Total Dynamic Head Summary and Definitions (26:51)
Section 4: Total Dynamic Head and Direct Measurements (14:02)
Section 5: Loop Analysis (24:08)
Unit C Quiz
UNIT D: Total Dynamic Head Practical Application
Unit D Reading
Section 1: TDH Analysis Overview and Labeling Nodes and Segments (14:08)
Section 2: Calculating Total Equivalent Pipe Length (20:16)
Section 3: Accounting for Parallel Segments and Static Head + Overall Results and Analysis (9:26)
Section 4: Further Analysis and Rules of Thumb (19:50)
Unit D Quiz
UNIT E: Total Dynamic Head Analysis Setup
Unit E Reading
Section 1: Watershape Advisor Worksheet Overview (12:39)
Section 2: Looking at the Example Project (15:05)
Section 3: Segments and Nodes (14:19)
Section 4: Calculating GPM (25:39)
Unit E Quiz
UNIT F: Total Dynamic Head Analysis
Unit F Reading
Section 1: GPM, Pipe Sizes and Segment A (20:14)
Section 2: Segments B, C, & D (28:56)
Section 3: Segment E (Filter and Heater) (11:24)
Section 4: Segments F, G, & H (11:21)
Section 5: Clean Up and Final Analysis (13:23)
Unit F Quiz
UNIT G: Pump Selection and Performance Curves
Unit G Reading
Section 1: Pump Performance Curves (30:58)
Section 2: Horsepower (19:05)
Section 3: Types of Pumps (31:11)
Section 4: Pump Details (19:37)
Unit G Quiz
UNIT H: Programmatic Planning
Unit H Reading
Section 1: Fluid Design Process and Shared Water Volumes (21:11)
Section 2: Turnover in the Watershape Advisor (25:00)
Section 3: Zones in the Watershape Advisor (20:21)
Section 4: Schematic Diagram and Pump Selection (22:10)
Unit H Quiz
UNIT I: Details
Unit I Reading
Section 1: Filters (16:04)
Section 2: Excavation (10:06)
Section 3: Pipe (29:35)
Section 4: Suction Outlets (30:31)
Section 5: Equipment Installations (13:07)
Unit I Quiz
UNIT J: Heating
Unit J Reading
Section 1: Heating Time and Heater Sizing (21:00)
Section 2: Weather Data and Thermal Expansion (6:50)
Section 3: Gas Pipe Sizing (32:31)
Unit J Quiz
UNIT K: Plumbing Details
Unit K Reading
Section 1: Ozone Details (22:36)
Section 2: Return Fittings, Jets, and Hartford Loops (12:18)
Section 3: Gauges and Meters (12:27)
Unit K Quiz
UNIT L: Schematic Diagrams
Unit L Reading
Section 1: Types of Schematic Diagrams (14:47)
Section 2: Diagram Rules of Thumb (15:19)
Section 3: Practical Application and Symbology (15:29)
Unit L Quiz
UNIT M: Watershape Advisor Worksheets
Unit M Reading
Section 1: Worksheet Application Review (19:35)
Section 2: Logarithmic Reduction and Ozone (27:44)
Section 3: Reference Tables (20:10)
Unit M Quiz
Course Conclusion
Manual Outro
Course Evaluation and Next Steps (13:06)
Section 1: GPM, Pipe Sizes and Segment A
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock